What's in your parts bin

keith dublin said:
So that means a new map ??
Click to expand...

yeah it would , but doubt i'll ever swap it back , as colm says a bung might be the best idea if one can be got ,
And Ciaran it a non resonated section , its probably the cause of the droning noise in the cabin ,
 
Will drop an email to Miltek and see if they do one , its not even that often i want it for , just 3 hours plus of motorway 120km with the same exhaust note boring a whole in your head , think ive remembered why i prefer driving the old roads over motorway
 
Tommy 555 said:
keith dublin said:
So that means a new map ??
Click to expand...

yeah it would , but doubt i'll ever swap it back , as colm says a bung might be the best idea if one can be got ,
And Ciaran it a non resonated section , its probably the cause of the droning noise in the cabin ,
Click to expand...

Yup I'd say so tommy why not get one when u got a few spare quid this is the one that went into mine might not fit ur miltec think they only fit each other
 

Attachments

  • image.jpg
    image.jpg
    145.3 KB · Views: 8
  • 0 bytes · Views: 8
  • 0 bytes · Views: 8
  • 0 bytes · Views: 8
for some reason miltek make a two and three quarter section so that deffo wont fit ,could ether keep an eye on s/n for resonated miltek or make a bung , or just dont drive long journeys in it lol , last few long trips we took her car for economy but i was not doing well without the power to overtake anything
 
I know the feeling 110km gives me 30mpg to cork and back no bad but boring Alrite at lest you have a 6th gear
 
Prodrive bug front bumper
prodrive twisted sideskirts
Sti side skirts
Defi gauges
Sti manifold complete
Jdm hid head lamps
 
white face Defis
Black face Defis
CDB machined for 2.1
Carl Davey billet fuel rail + fuel system
Rcm manifold+ venturi up-pipe
Carl Davey up-pipe
Zen 3 port map sensor
Zen new age coil conversion
Zero sport gauge holder
Forge header tank
Reverse inlet manifold
Carl Davey alternator kit

cant think of anymore
Complete super pro bushing kit
 
Same as Luke all the parts are on the car, any parts not on it are for the bin :icon_grin:
 
1) Porsche GT3 RS calipers
2) Front alloy wishbones with Whiteline bushes and AntiLiftKit
3) Whiteline Roll Centre -bump steering kit
4) A set of brand new 18" Rotas in white
5) Hayward and Scott complete exhaust, to replace my too noisy 3" Kakimoto.
 
sc46 , alcatek and a few supporting mods , nothing major . :icon_grin:


getting sick of looking at them in wardrobe . :banghead


need to sort wheel situation aswell :lol2 :lol2 :lol2
 
images



1st refusal :thumbsup:
 
nothing special for me, just a cultch kit i got 2 years ago, new CV joints, service parts and a few odd bits and bobs that i have put up and cant find
 
Bought a load of Whiteline bits to address the suspension at the end of the year that aren't on the car yet.

W61383 Trailing arm - lower rear bushing
W61381 Trailing arm - lower front bushing
W91379 Diff - support outrigger bushing
W92835 Diff - mount in cradle bushing
W61382 Control arm - lower inner & outer bushing
KSR206 Steering - rack & pinion mount bushing
KCA313 Roll centre/bump steer - correction kit
W52837 Control arm - lower inner front bushing

Really want to get a set of BC BRs like Baz and fit them with the above, but with the job situation up in the air holding off on buying the coilovers and hence the WL stuff sitting in the shed till needed. :icon_sad:

Still have a solid rear gear link bush as well to be fitted which I got from Cobb last year... easy job to do, but need to take the surround of the gear lever again and hate those fiddly nuts that fall off and then need to hunt for and stick back in place with some superglue - near bloody glued my fingers to the stupid thing last time LOL.
 
You must log in or register to reply here.
Back
Top